Модули хурд Дучандон Flank Gear Rolling Tester

The product adopts the marble base and the structure of "micro-force parallel slider" as the measuring unit, which makes the operation smooth and flexible.The tested mandrel adopts a universal PIN shaft to facilitate the replacement of the test product, and it can also be customized according to the test product. The product adopts high precision network port communication motion control and error data acquisition system, which can automatically measure theradial composite deviation Fi",Radial composite deviation fi" and radial runout Fr" of the gear at one time.Center distance movement upper and lower deviation (Eas, Eai),The distance across rollers (M) and common normal line (Wk) of gear side backlash were detected in the center distance measurement mode. Quickly confirm the location of gear burr points and bumps, and perform online maintenance to meet and continue to develop new measurement requirements put forward by users.

Маводҳо ва параметрҳои андозагирии асбобҳо

1. Инҳирофшавии таркибии радиалӣ: (Fi〞）；

2. Кафолати радиалии дандон ба дандон: (fi〞）；

3. Хуруҷи радиалӣ: (F_r〞）；

4. Хатти муқаррарии умумӣ: (W);

5. Масофаи байни роллерҳо: (M);

6.Center distance movement upper and lower deviation: (Осон,Эй);

Параметрҳои асосии техникӣ

1.Module of measuredgear --------------------------------------------------- 0.2~2 mm

2.Max.OD of measured gear----------------------------------------------------- 100 mm

3.Double flank center distance------------------------------------------------ 20~90 mm

4. Distance between double flank tips ---------------------------------------70-120mm

5.Micromotion measures the movement of the slide frame------------------ 5 mm

6.Spindle Load----------------------------------------------------------------------------- 2Kg

7.Instrument accuracy:

Истинод ба GB / T26093-2010 "Асбоби ҳамаҷонибаи ченаки фишанги дуҷонибаи mesh" стандарти таҳия шудааст, ки стандартҳои қабулро мувофиқи он татбиқ кардан мумкин аст (ниг. Замимаи 1).

8.Instrument repeatability:

Radial composite deviation Fi", Tooth-to-tooth radial deviation fi" and radial runout Fr"(repeatability аст0.003mm);

The common normal line Wk andthe distance across rollers M(repeatability0.005мм аст);

(Ҳар як чархи ченкунӣ ва қисмҳои корӣ аз як дандон оғоз мешаванд);

1. Adopt the structure layout of the centered measuring unit to avoid bias and facilitate gear installation;

2.The equipment detection movement unit adopts "precision" V-shaped guide rail. Its friction, small clearance, small inertia, smooth and flexible operation is more suitable for the detection of tiny gear.

3.The standard gear shaft and the workpiece gear shaft are made of dense steel ball rolling shafting, low friction resistance, high measurement accuracy (the minimum tool cage can be processed to the inner diameter of 2mm);

4. The equipment meshing micro force measurement breaks the traditional fixed force measurement method, and changes to the adjustable force measurement method according to the measurement accuracy requirements of different products.

5.The software can set the measurement speed, mesh rotation direction, the measurement beat is 2~18S can be adjusted;

6.The use of electric system for automatic tooth splitting;

7.Qнуқтаи бурриши фишанг, мавқеи зарбаро ба таври фаврӣ тасдиқ кунед, ба оператор барои нигоҳдории онлайн муроҷиат кунед, диапазони шинохти хатогиҳои ченкунӣ аз 0.01 мм зиёдтар аст;

8.Through the three-color light display measurement results;

9.The standard gear installation diagram, the inner hole diameter of the standard wheel φ20 (+0.003/0);

10.According to the use of the site environment for the computer to usedust-proof, anti-oil mist chassis and install the ventprotection device to ensure the computer life;

11.Сарпӯши муҳофизатии асбобро пурзӯр кунед, то ба муҳаррик ворид шудани равғанро пешгирӣ кунед ва ба мӯҳлати хидмат таъсир расонад;

12.Disk gear detection;

13.Upgrade to the win10 environment measurement software;